Master of Science in Process Technology: Nye registreringer
Viser treff 81-100 av 177
-
Closing the plastic waste material cycle in the power industry
(Master thesis, 2021)Cables and wires are widely used in electronic equipment and power industry for transmission of both data and electricity, where the rapid development of power lines and constant update of electronic devices have resulted ... -
This report forms part of the basis for assessing the student’s performance in the course
(Master thesis, 2020)The reject water of any wastewater treatment plant (WWTP) contains carbon dioxide (CO2) and micro-organisms. The environmental biotechnology research group of the University of South-Eastern Norway (USN) is trying to ... -
Assessment of CFD methods in predicting flow regime and pressure gradient in two phase gas-liquid vertical flow
(Master thesis, 2020)Available tools for dealing with multi-phase flows are not effective with complex geometries such as process piping with combination of horizontal and vertical pipes, bends and valves. However, rapid development of ... -
Computational modeling of fluidized bed behavior with agglomerates.
(Master thesis, 2020)The transition towards the use of more renewable energy is an essential subject for the imminent climate crisis. Biomass can be converted into syngas in a gasification process. The formation of agglomerates in a Bubbling ... -
Utilization of excess heat from data centers.
(Master thesis, 2020)Digitalization has influenced the rapid growth of data centers around the world. The advancement of IT and telecommunication also played a vital role in is this expansion of data centers. Data centers facilitate the ... -
Software Testing, Data Security and GDPR
(Master thesis, 2019)Software and data security are an important part of a modern-day business strategy of any organization as it forms the basis for guaranteed security of information, data, and assets of any organization. This project is ... -
Gas-to-gas heat exchanger for heat utilization in hot CO2 from an electrically heated calcination process
(Master thesis, 2019)Thesis was done with the objective of evaluating a gas to gas heat exchanger which will be used to recover heat from hot calciner exit gas from an electrically heated calcination process. Shell and tube heat exchanger ... -
Change in flame front area over time with premixed combustion across an obstacle
(Master thesis, 2018)This thesis is a joint project of USN, and CMR Gexcon to explore the changes in flame front area over time with premixed combustion across an obstacle. The objective of this thesis is to make a literature review on ... -
Use of Process Analytical Technology (PAT) as on-line measurement technique for pipe erosion due to particle impact
(Master thesis, 2018)Solid particle impact is getting enormous attention due to rapid progress and development in coal conversion plant, where flows of solid particles are sky-scraping at various equipments of plant. Such particles flow can ... -
Reduction in Sulphur Emissions from the Norcem Cement Plant in Kjøpsvik
(Master thesis, 2018)SO2 emissions in the stack gas from the Norcem cement plant in Kjøpsvik was significantly higher than the permitted emission limit in 2017. The plant aims to reduce the emissions by installing a seawater flue gas ... -
Boil-off gas handling for LNG-carriers with a low-swirl burner
(Master thesis, 2018)Wärtsilä is looking into a new technology for boil-off gas handling. The technology chosen for further research is a low-swirl burner. This burner has shown promising NOx emission results which is a problem inside the ... -
Computational modeling and experimental studies on fluidized bed regimes
(Master thesis, 2018)The fluidization technology has a wide range of applications from chemical synthesis to pneumatic transportation and circulation of species. Different process applications require different flow regimes and the type of ... -
Pyrolysis of plastic waste into green fuels – experimental study
(Master thesis, 2018)Recycling of plastic waste in more environmental friendly ways is under great attention. Catalytic pyrolysis of plastic waste is among the sustainable methods that can recover valuable products from plastics. However, ... -
Measurement and correlation of aqueous amine solution viscosities
(Master thesis, 2016)The viscosities of amines are important in designing equipment for Carbon dioxide (CO2) capture as it affects heat transfer coefficient, pressure drop in heat exchangers and piping system respectively. Reliable viscosity ... -
Flame length measurements of hydrogen jets
(Master thesis, 2017)The use of hydrogen is increasing rapidly and the research on hydrogen safety must follow. The implementation of hydrogen filling stations and cars are steadily on the rise. In the case of a leakage the hydrogen will most ... -
Simulation and control of hydro power plants
(Master thesis, 2017)Sustainable energy development implies meeting the energy needs of the future without jeopardizing the life quality of the planet. To achieve these goals is possible by gradually replacement in energy production profile ... -
Waste heat availability in the raw meal department of a cement plant
(Master thesis, 2017)The main aim of this study was to find out the available heat of the exhaust gas stream that is bypassed through the raw meal department at Norcem Brevik cement plant, Norway which produces about 1 million ton of clinker ... -
Li-ion battery safety
(Master thesis, 2017)The aim of this thesis was two folded: Numerically compute the combustion properties of the discharge materials from lithium-ion batteries, and experimentally measure the properties, at a test rig, by overheating lithium-ion ... -
Experimental Study of Catalysis in Plastic Pyrolysis
(Master thesis, 2017)In this study, thermal and catalytic pyrolysis of high-density polyethylene (HDPE), low-density polyethylene (LDPE), polypropylene (PP) and mixtures of LDPE/PP plastics were carried out in a batch autoclave reactor at 460 ... -
Comparison of CO2 dehydration processes after CO2 capture
(Master thesis, 2017)This study compares two conventional methods of CO2 dehydration processes after CO2 capture and its suitability of use. The methods are Triethylene Glycol (TEG) absorption and 3A Molecular sieve adsorption. Chapter 1 and ...