Blar i Master of Science in Process Technology på tittel
Viser treff 15-34 av 147
-
CO2 capture solvent performance characterization
(Master thesis, 2015-09-25)The aim of this work is to determine partial pressures and CO2 loadings of primary amine aqueous solutions such as monoethanolamine, 3-amino-1-propanol, 4-amino-1-butanol and 5-amino-1-pentanol at the equal vapor liquid ... -
CO2 Enhanced Oil Recovery in Reservoirs with Advanced Wells; Simulations and Sensitivity Analysis
(Master thesis, 2024)The global climate challenge from CO2 emission leading to adverse climate conditions requires action to reduce its emission into the world. The process of CO2 enhanced oil recovery is one of the actions that can contribute ... -
CO2 for enhanced oil recovery and secure storage of CO2 in reservoirs
(Master thesis, 2015-10-30)CO2-EOR(Enhanced Oil Recovery) is an effective and useful technology that can not only increase the oil production to meet the increasing need for energy around the world, but also mitigate the negtive influence of global ... -
Comparing methods for system identification on the quadruple tank
(Master thesis, 2015-10-30)System Identification in control engineering has been the field of interest for the research and development to find the optimal model of dynamic system. Both MIMO and SISO systems can be modeled using different system ... -
Comparison of CO2 dehydration processes after CO2 capture
(Master thesis, 2017)This study compares two conventional methods of CO2 dehydration processes after CO2 capture and its suitability of use. The methods are Triethylene Glycol (TEG) absorption and 3A Molecular sieve adsorption. Chapter 1 and ... -
Computational modeling and experimental studies on fluidized bed regimes
(Master thesis, 2018)The fluidization technology has a wide range of applications from chemical synthesis to pneumatic transportation and circulation of species. Different process applications require different flow regimes and the type of ... -
Computational modeling of fluidized bed behavior with agglomerates.
(Master thesis, 2020)The transition towards the use of more renewable energy is an essential subject for the imminent climate crisis. Biomass can be converted into syngas in a gasification process. The formation of agglomerates in a Bubbling ... -
Computational Study of CO2 Injection for Enhanced Oil Recovery and Storage
(Master thesis, 2023)After a while of oil production from reservoir, pressure of reservoir will be decreased, and the rate of production will be decreased too as a result some oil will remain in the reservoir. One of the main problems is ... -
Computational study of heat transfer in subsea deadlegs for evaluation of possible hydrate formation
(Master thesis, 2007)The background for this project is the request of achieving more knowledge of the temperature and velocity fields in different subsea deadleg geometries. This is important to avoid hydrate formation in subsea equipment. ... -
Control system for mass flow rate of solids in pneumatic conveying
(Master thesis, 2008-06-06)The aim of the thesis is to make a model of the mass flow rate of solids in the pneumatic conveying systems situated at the POSTEC/Tel-Tek research facility to be used for the testing of model predictive control of these ... -
Cost estimation of CO2 removal in HYSYS
(Master thesis, 2010-10-18)A Hysys simulation of a CO2 capture process by absorption in a monoethanol amine (MEA) solution from the flue gas from a 500 MW natural gas power plant has been developed as a verification of earlier simulations at TUC. ... -
CO₂ dehydration after CO₂ capture
(Master thesis, 2016)The presence of free water is considered as one of the major impurities for the pipeline transportation of gas. Corrosion and hydrate formation in the process plant equipment are common problems associated with the free ... -
Data Analysis and Modelling of Induction Hardening Processes
(Master thesis, 2023)In collaboration with ENRX, this project conducted a technical feasibility study focused on data collection and analysis. The project involved gathering operational data from induction hardening machines owned by various ... -
Density and viscosity correlations and thermodynamic properties in post-combustion CO2 capture processes
(Master thesis, 2022)Physicochemical properties such as density and viscosity are critical in the design of process equipment in the post combustion amine-based CO2 capture process because they appear in the majority of the mass transfer and ... -
Design and construction of a bubbling fluidized bed reactor with two side nozzles as inlet flow boundary condition
(Master thesis, 2023)Fluidized bed reactors are commonly used in industrial applications such as waste to energy conversion, chemical synthesis, granulation, catalyst regeneration, biomass gasification, pyrolysis, etc. They are used in such ... -
Design av desentraliserte og suboptimale regulatorer for diskrete systemer
(Master thesis, 2005)Denne rapporten beskriver hvordan optimaliseringproblemet knyttet til optimalregulering, kan løses ved hjelp av optimaliseringsrutiner. En algoritme er laget og implementert i MatLab versjon 6.5 (R13) for optimal innstilling ... -
Design of Fine Powder Handling System Enhancing the Circularity of Aluminium Production
(Master thesis, 2023)Hydro Aluminium wants to separate fine powder particles (filter dust) from the process and send them to a specifically built storage silo by a pneumatic conveying line to mix with basement dust and feed back into the main ... -
Determination of particle velocities in pneumatic conveying
(Master thesis, 2015-10-09)The main objective of this investigation was to formulate a technique for particle velocity determination in pneumatic conveying system. Plastic pellets were transported in a pneumatic conveying experimental rig. A large ... -
Deterministic flood control using MPC on the Kragerø waterways
(Master thesis, 2015-11-06)The Kragerø Waterways consist of 5 power plants downstream after Lake Toke, Dalsfos is the first of these power plants. As a deterministic flood control of Lake Toke and Dalsfos there has been designed a MPC. The MPC uses ... -
Detonations in fuel-oxygen mixtures
(Master thesis, 2015-09-18)A brief literature study was carried out to learn more about detonations, deflagrations, shock waves and critical tube diameters. A comprehensive experimental test rig was assembled based on an earlier test rig. The rig ...